 |
上海志銘實業有限公司
主營產品： 烤魚爐,大型烤魚爐,鐵板燒,鐵板燒設備,原子彈烤肉設備 |
|
上海志銘實業有限公司
主營產品： 烤魚爐,大型烤魚爐,鐵板燒,鐵板燒設備,原子彈烤肉設備 |
2015-2-9 閱讀(1030)
志銘實業·燃氣加熱鐵板燒設備操作說明
1、首先開啟風機電源，檢查抽風系統，正常后再進行下一步操作。
2、然后打 開火種燃氣開關，按下點火按鈕，查看關火孔內苗火是否點燃。
3、苗火點燃后，打開主火開關，便可正常使用。
4、zui后調整燃氣開關大小至合適狀態，以控制燃火器火焰強弱。
1, first open the fan power supply, check the convulsions system, on to the next step after normal operation.
2, then open the fire gas switch, ignition button, check off the fire hole seedling fire is lit.
3, seedling after the fire, open the main switch, fire can be normal use.
4, adjust gas switch size to the appropriate state, to control the strength of flame combustion firearms.
志銘實業·電加熱鐵板燒設備操作說明
A、首先開啟風機電源，檢查抽風系統，正常后再進行下一步操作。也可以暫時關閉排煙風機，等實際操作時再開啟。
B、然后按下電源按鈕，設備進入待機狀態，按下加熱啟動按鈕，加熱系統進入加溫狀態，直至溫度達到設定上*停止。zui后設備的加熱原件會在數字溫控的控制下，在上限和下限溫度之間循環工作。
C、溫控設定流程：首先，打開電源開關，電源燈亮，開啟動摯，按SET0.5秒屏幕顯示CC。
注：1、LOCK值0為kaisuo，1為閉鎖，其他為出廠設置，禁止更改。
2、PH溫度上限值嚴禁超過380℃。
3、將CC設定成上限下限之間的差值（即上限減去下限值）。
4、將P設成0。
5、SV值設定成要求值減去1/2CC值。
例：要上限100℃，下限80℃，將CC設定成20℃，P設定成0，SV設成90℃，儀表到100℃時停止工作，到80℃時開始工作。
A, first open the fan power supply, check the convulsions system, on to the next step after normal operation. Also can temporarily closed exhaust fan, such as the actual operation and open.
B, then press the power button, the device has reached the standby mode, press the heating start button, heating heating system into the state, until the set temperature is reached on time to stop. The heating of the original equipment. Will be under the control of the digital temperature control, between the upper and lower limit temperature cycle work.
C, set the temperature control process: first, open the power switch, the power lights, open start zhi, according to the screen display CC SET0.5 seconds.
Note: 1, 0 to unlock the LOCK values, 1 for closure, the other as the factory Settings, change is prohibited.
2, PH, temperature limit do not exceed 380 ℃.
3, set the CC into the difference between the upper limit lower limit value (that is, the upper limit minus the lower limit value).
4, will be set to 0 P.
5, SV set values to the required value minus 1/2 cc.
Example: to maximum of 100 ℃, the lower limit of 80 ℃, 20 ℃, your CC set to 0, P SV set to 90 ℃, the meter to the 100 ℃ when to stop working, and begins to work up to 80 ℃.
