進口水用過濾器(德國奧萊斯OLES閥門)
【進口水用過濾器】詳細說明：
本過濾器有殼體、排污蓋、濾芯、濾網等組成。網眼總面積是入口管首截面積的3-4倍。用于管道清除輸送介質:熱水、冷水、蒸汽、壓縮空氣各種機械雜質,特別是鍋爐房循環水泵前均需安此產品,為了清除系統中的機械雜質,使設備和管道免受堵塞和磨損,在額定流速下壓損為0.05-0.1米水柱。用于各種用汽設備,如:蒸汽儀表、疏水閥,壓縮空氣和各類用汽設備前均需安裝。在額定流速下壓損為0.05-0.2米水柱。油過濾器該主品濾眼密度有多種。例如:64孔、200孔、300孔/Cm2。用于各種輸油管道上一切設備。例如:油泵、油鍋爐前均需安裝,在額定流速下壓損為0.05-0.1米水柱
The filter consists of a shell, a drainage cover, a filter element, a filter screen, etc. The total area of mesh is 3-4 times of the cross-sectional area of the inlet pipe head. For pipeline cleaning conveying media: hot water, cold water, steam, compressed air all kinds of mechanical impurities, especially before circulating water pump in boiler room, this product should be installed. In order to remove mechanical impurities in the system, so that equipment and pipelines are free from clogging and wear, pressure loss is 0.05-0.1 m water column at rated flow rate. For all kinds of steam equipment, such as steam meters, traps, compressed air and all kinds of steam equipment need to be installed before. Pressure loss is 0.05-0.2 m water column at rated flow rate. Oil filter The main product has a variety of filter density. For example: 64 holes, 200 holes, 300 holes/Cm2. It is used for all kinds of equipment in oil pipelines. For example, oil pumps and oil boilers need to be installed before the pressure loss is 0.05-0.1 m water column at rated flow rate
【進口水用過濾器】工作原理;
該產品安裝于進水管路中各配套閥門的前端，當管道中的介質首*入過濾器時，介質通過濾網進入被連接的閥門中，而雜質則留于過濾桶內，使各類閥門不會由于機械雜物卡入密封圈而失靈。
【進口水用過濾器】特點：
1.進出口通徑：原則上過濾器的進出口通徑不應小于相配套的泵的進口通徑一般與進口管路口徑*。
2.公稱壓力：按照過濾管路可能出現的zui高壓力確定過濾器的壓力等級。
3.孔目數的選擇：主要考慮需攔截的雜質粒徑依據介質流程工藝要求而定。通水網為18-30目、通氣網為40-100目、通油網為100-480目。
4.過濾器材質：過濾器的材質一般選擇與所連接的工藝管道材質相同對于不同的服役條件可考慮選擇鑄鐵、碳鋼、低合金鋼或不銹鋼材質的過濾器。
5.過濾器阻力損失計算：在一般計算額定流速下壓力損失為0.52～1.2kpa。
產品應用范圍：
1.進出口通徑：原則上過濾器的進出口通徑不應小于相配套的泵的進口通徑一般與進口管路口徑*。
2.公稱壓力：按照過濾管路可能出現的zui高壓力確定過濾器的壓力等級。
3.孔目數的選擇：主要考慮需攔截的雜質粒徑依據介質流程工藝要求而定。通水網為18-30目、通氣網為40-100目、通油網為100-480目。
4.過濾器材質：過濾器的材質一般選擇與所連接的工藝管道材質相同對于不同的服役條件可考慮選擇鑄鐵、碳鋼、低合金鋼或不銹鋼材質的過濾器。
5.過濾器阻力損失計算：在一般計算額定流速下壓力損失為0.52～1.2kpa。
